Because goats have feelings too:

https://steadfastandloyal.com/unreal/man-arrested-for-goat-fondling-and-more-claims-it-was-consensual/?utm_source=spotim&utm_medium=spotim_recirculation&spotim_referrer=recirculation&spot_im_comment_id=sp_cLNLhA82_17065_c_sIrQJ8

"One thing could bring him down and that’s if President Trump nominates him for the Supreme Court."

Splat!

TOLERANCE: Tolerance is the allowable variation for any given size in order to achieve a proper function. Tolerance equals the difference between lower and upper limit dimensions. Example; for 0.500-0.506 inch the tolerance would be 0.006 inch.

BILATERAL TOLERANCE : It is a way to express tolerance by using both minus and plus variations from a given size. Example;
inch. The limit dimensions are 1.120-1.130 inch. The tolerance is 0.010 inch.

UNILATERAL TOLERANCE is a way to express tolerance by using only minus or plus variation from a given size.

FIT : The general term of fit to describe the range of tightness designed into parts which assemble one into another. The fit can be explained under the three categories:

A-CLEARANCE FIT is a type of fit in which one part fits easily into another with a resulting clearance gap.

A clearance fit. The shaft is always smaller than the hole
Tolerance on shaft : 0.002
Tolerance on hole : 0.002
minimum clearance : 0.600 - 0.595 = 0.005 inch
maximum clearance : 0.602 - 0.593= 0.009 inch
The 0.005 clearance is for the tightest possible fit.


B-FORCE (INTERFERENCE) FIT is a type of fit in which one part must be forcibly fitted into another.

A-FORCE (INTERFERENCE) FIT is when the shaft is always larger in diameter than the hole, parts must be assembled by pressure or heat expansion.
Tolerance on shaft : 0.001
Tolerance on hole : 0.001
minimum clearance : 0.500 - 0.503= -0.003 in (the tightest fit 0.003 in interference)
maximum clearance : 0.501 - 0.502 = -0.001 in (the loosest fit 0.001 in interference)
Maximum clearance=Minimum interference
Minimum clearance=Maximum interference
C-TRANSITION FIT : A type of fit in which loosest case provides a clearance fit and the tightest case gives an interference fit. See the example below,

A transition fit exists when the maximum clearance is positive and the minimum clearance is negative
Tolerance on shaft : 0.005
Tolerance on hole : 0.005
minimum clearance : 0.500 - 0.507 = -0.007 inch
The tightest fit is 0.007 in interference.
maximum clearance : 0.505 - 0.002 = 0.503 inch
The loosest fit is 0.003 in clearance
Transition fits are used only for locating a shaft relative to a hole,
where accuracy is important but either a clearance or interference is permitted.


ALLOWANCE : An alternative expression for tightest possible fit, which is minimum clearance or maximum interference.

BASIC-SHAFT SYSTEM : This is a system in which the basic size is included as one of the limit dimensions of the shaft. But it is not for the hole. As an example: For a basis size of 1.000 inch. The limit dimensions on the shaft could be 1.000 and 1.005 inch. The related hole could be 1.011 and 1.018 inch.
BASIC-HOLE SYSTEM : This is a system in which the basic size appears as one of the limit dimensions of the hole. But it is not for the shaft. As an example for a basic size of 1.000 inch, the limit dimensions of the hole might be 1.000 and 1.007 inch. For the related shaft the limit dimensions could be 0.994 and 0.989 inch.
MINIMUM MATERIAL CONDITION : In this condition a hole is at its largest limit dimension. A shaft is at its smallest limit dimension. This condition exists at maximum clearance or minimum interference.
MAXIMUM MATERIAL CONDITION : In this condition a hole is at its smallest limit dimension. The shaft is at its largest limit dimension. This condition exists at minimum clearance or maximum interference. See example under the Force fit condition.

Tolerance, in a nutshell, defines the minimum standards of measurement to ensure a quality product.

Yep, you nailed it:

https://www.latimes.com/local/lanow/la-me-ln-womens-march-canceled-20190102-story.html

Not far enough. As I understand it, there'a big black hole at the center of the Milky Way. Send him past the event horizon and I'll be satisfied.

Yes, another country without an internet connection, like on some parallel universe somewhere far, far away.

They can deafen themselves and everyone around them, the facts will not change because a bunch of fools are yelling about it. No crime, no indictment. Period. Actually, I think it's kind of funny that they stand there stamping their feet like spoiled little brats who just got told 'no'. When my children were small I'd give them a spanking for that.

I don't see any correlation.

The hyperbole over impeaching the President certainly undermines the credibility of those politicians who are screeching about it, if they have any credibility left to undermine. In order to press charges, there must be first a victim, then a crime. In President Trump's case, there are neither victim nor crime, so impeachment (the pressing of charges) is a non-starter.

As for the stock markets; they expand and collapse all the time, nothing new there, and the dollar collapse is a function of it finding its intrinsic value, which it eventually must, regardless of the political climate around it (Hint, it's zero, unless you count the value of the paper it's printed on).

As for what Democrats care about, that's more a 'touchy-feely' thing than any logically reasoned value system. They care most about what makes them 'feel' good, like the $15 minimum wage that is about to put half the unskilled people in America out of work, but Democrats feel good about it because they gave everyone a pay raise. See how that works? And as a bonus, they get to blame the President for the high unemployment!

Her (it's?) trial date is scheduled for March 4.

Congressmen can be censured or impeached by their peers, but the only way for the rest of us to 'fire' a congressman is to vote him/her out at the next election. Good luck with that.

Unfortunately...

You've been drinking again, haven't you?

When my (then) new wife started that 'seat down' crap, I readily agreed to her request, on the condition that she leave the seat up when she's done. Didn't happen and it shut her up, because every time she mentioned it I reminded her of my offer.

Don't worry, I let her win plenty of times. Even during the divorce, I just let her dictate terms and said 'yes, dear' a lot. She finally drew the line when we went into a MacDonald's and I ordered a 'McPickle'. After more than 20 years, she just couldn't take it any more and made me sign the decree. She always hated the 'McPickle'.

They must be trying to compete with UCLA:

Due to seemingly popular demand, the UCLA have actually combined queer theory – the study of gender, feminism and gayness – with the science of music, to produce a very open-minded course within their Herb Alpert School of Music. The LA Times reported that the course will introduce debates like: “the idea that if you’re gay, then music by gay composers such as Benjamin Britten will sound different to you than it would if you were straight.”

Welcome to your PhD in 'Queer Musicology'!

Shh! It's a secret!

No, he can't. And the Congress cannot force the President to sign any legislation either. How far do you think this bill will go if it leaves the Senate?